PCA9509DP

Level translating I2C-bus/SMBus repeater

Generaldescription ThePCA9509isaleveltranslatingI2C-bus/SMBusrepeaterthatenablesprocessorlowvoltage2-wireserialbustointerfacewithstandardI2C-busorSMBusI/O.WhileretainingalltheoperatingmodesandfeaturesoftheI2C-bussystemduringthelevelshifts,italsopermitse

PHI

PCA9509DP

Level translating I2C-bus/SMBus repeater

Generaldescription ThePCA9509isaleveltranslatingI2C-bus/SMBusrepeaterthatenablesprocessorlowvoltage2-wireserialbustointerfacewithstandardI2C-busorSMBusI/O.WhileretainingalltheoperatingmodesandfeaturesoftheI2C-bussystemduringthelevelshifts,italsopermitse

ETC

PCA9509DP

Level translating I2C-bus/SMBus repeater; Bidirectional buffer isolates capacitance and allows 400 pF on port B of the device\nVoltage level translation from port A (1.35 V to VCC(B) ? 1.0 V) to port B (3.0 V to 5.5 V)\nRequires no external pull-up resistors on lower voltage port A\nActive HIGH repeater enable input\nOpen-drain inputs/outputs\nLock-up free operation\nSupports arbitration and clock stretching across the repeater\nAccommodates Standard-mode and Fast-mode I2C-bus devices and multiple masters\nPowered-off high-impedance I2C-bus pins\nOperating supply voltage range of 1.35 V to VCC(B) ? 1.0 V on port A, 3.0 V to 5.5 V onport B\n5 V tolerant port B SCL, SDA and enable pins\n0 Hz to 400 kHz clock frequency\nRemark: The maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater.\nESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101\nLatch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA\nPackages offered: TSSOP8, SO8, XQFN8\n;

The PCA9509 is a level translating I2C-bus/SMBus repeater that enables processor lowvoltage 2-wire serial bus to interface with standard I2C-bus or SMBus I/O. While retainingall the operating modes and features of the I2C-bus system during the level shifts, it alsopermits extension of the I2C-bus by providing bidirectional buffering for both the data(SDA) and the clock (SCL) lines, thus enabling the I2C-bus or SMBus maximumcapacitance of 400 pF on the higher voltage side. Port A allows a voltage range from1.35 V to VCC(B) ? 1.0 V and requires no external pull-up resistors due to the internalcurrent source. Port B allows a voltage range from 3.0 V to 5.5 V and is overvoltagetolerant. Both port A and port B SDA and SCL pins are high-impedance when thePCA9509 is unpowered.\nFor applications where Port A VCC(A) is less than 1.35 V or Port B VCC(B) is less than 3.0 V,use drop-in replacement PCA9509A.\nThe bus port B drivers are compliant with SMBus I/O levels, while port A uses a currentsensing mechanism to detect the input or output LOW signal which prevents bus lock-up.Port A uses a 1 mA current source for pull-up and a 200 Ω pull-down driver. This results ina LOW on the port A accommodating smaller voltage swings. The output pull-down on theport A internal buffer LOW is set for approximately 0.2 V, while the input threshold of theinternal buffer is set about 50 mV lower than that of the output voltage LOW. When theport A I/O is driven LOW internally, the LOW is not recognized as a LOW by the input.This prevents a lock-up condition from occurring. The output pull-down on the port Bdrives a hard LOW and the input level is set at 0.3 of SMBus or I2C-bus voltage levelwhich enables port B to connect to any other I2C-bus devices or buffer.\nThe PCA9509 drivers are not enabled unless VCC(A) is above 0.8 V and VCC(B) is above2.5 V. The enable (EN) pin can also be used to turn on and turn off the drivers undersystem control. Caution should be observed to change only the state of the EN pin whenthe bus is idle.\n

恩XP

9509

ComputerCableforEIARS-232Applications

9509

RS-232,#24-9pr,SR-PVC,O/AFoil,PVCJkt,CMG,75Ω

ProductDescription ComputerEIARS-232Cable,24AWGstranded(7x32)tinnedcopperconductors,semi-rigidPVCinsulation,9twistedpairs,overallBeldfoil?shield(100 coverage),24AWGstrandedtinnedcopperdrainwire(continued),PVCjacket.

9509

MACHINESCREWPANPHILLIPS10-32