首頁>PCA9575PW2>規格書詳情

PCA9575PW2集成電路(IC)的I/O擴展器規格書PDF中文資料

PCA9575PW2
廠商型號

PCA9575PW2

參數屬性

PCA9575PW2 封裝/外殼為28-TSSOP(0.173",4.40mm 寬);包裝為卷帶(TR)剪切帶(CT)Digi-Reel? 得捷定制卷帶;類別為集成電路(IC)的I/O擴展器;產品描述:IC I2C/SMBUS 16BIT GPIO 28-TSSOP

功能描述

16-bit I2C-bus and SMBus, level translating, low voltage GPIO with reset and interrupt

絲印標識

PA9575PW2

封裝外殼

TSSOP28 / 28-TSSOP(0.173",4.40mm 寬)

文件大小

632.01 Kbytes

頁面數量

44

生產廠商 NXP Semiconductors
企業簡稱

nxp恩智浦

中文名稱

恩智浦半導體公司官網

原廠標識
數據手冊

下載地址一下載地址二到原廠下載

更新時間

2025-4-25 17:53:00

人工找貨

PCA9575PW2價格和庫存,歡迎聯系客服免費人工找貨

PCA9575PW2規格書詳情

1 General description

The PCA9575 is a CMOS device that provides 16 bits of General Purpose parallel Input/Output (GPIO)

expansion in low voltage processor and handheld battery powered mobile applications and was developed to enhance the NXP family of I2C-bus I/O expanders. The improvements include lower supply current, lower operating voltage of 1.1 V to 3.6 V, separate supply rails to allow voltage level translation anywhere between 1.1 V and 3.6 V, 400 kHz clock frequency, and smaller packaging. Any of the 16 I/O ports can be configured as an input or output independent of each other and default on start-up to inputs. I/O expanders provide a simple solution when additional I/Os are needed while keeping interconnections to a minimum; for example in battery powered mobile applications and clamshell devices for interfacing to sensors, push buttons, keypad, etc. In addition to providing a flexible set of GPIOs, it simplifies interconnection of a processor running at one voltage level to I/O devices operating at a different (usually higher) voltage level. PCA9575 has built-in level shifting feature that makes these devices extremely flexible in mixed signal environments where communication between incompatible I/Os is required. The core of PCA9575 can operate at a voltage as low as 1.1 V while each I/O bank can operate in the range 1.1 V to 3.6 V. Bus hold with programmable on-chip pull-up or pull-down feature for I/Os is also provided. The output stage consists of two banks each of 8-bit configuration registers, input registers, interrupt mask registers, output registers, bus-hold and pull-up/pull-down registers and polarity inversion registers. These registers allow the system controller to program and configure 16 GPIOs through the I2C-bus. The system controller can enable the I/Os as either inputs or outputs by writing to the I/O configuration register bits. The data for each input or output is kept in the corresponding Input or Output register. The polarity of the read registers can be inverted with the Polarity Inversion register (active HIGH or active LOW operation). Either a bus-hold function or pull-up/pull-down feature can be selected by programming corresponding registers. The bus-hold provides a valid logic level when the I/O bus is not actively driven. When bus-hold feature is not selected, the I/O ports can be configured to have pull-up or pull-down by programming the pull-up/pull-down configuration register. An open-drain interrupt output pin (INT) allows monitoring of the input pins and is asserted each time a change

occurs on an input port unless that port is masked (default = masked). A ‘GPIO All Call’ command allows

programming multiple PCA9575s at the same time even if they have different individual I2C-bus addresses. This command allows optimal code programming when more than one device must be programmed with the same instruction or if all outputs must be turned on or off at the same time. The internal Power-On Reset (POR) or hardware reset pin (RESET) initializes the two banks of 8 I/Os as inputs, sets the registers to their default values and initializes the device state machine. The I/O banks are held in its default state when the logic supply (VDD) is off. The PCA9575 is available in 24-pin TSSOP, 28-pin TSSOP and HWQFN24 packages, and is specified over the -40 °C to +85 °C industrial temperature range, with HWQFN24 up to +105 °C. The 28-pin package provides four address select pins, allowing up to 16 PCA9575 devices to be connected with 16 different addresses on the same I2C-bus.

2 Features and benefits

? Separate supply rails for core logic and each of the two I/O banks provides voltage level shifting

? 1.1 V to 3.6 V operation with level shifting feature

? Very low standby current: < 2 μA

? 16 configurable I/O pins organized as 2 banks that default to inputs at power-up

? Outputs:

– Totem pole: 1 mA source and 3 mA sink

– Independently programmable 100 kΩ pull-up or pull-down for each I/O pin

– Open-drain active LOW interrupt (INT) output pin allows monitoring of logic level change of pins

programmed as inputs

? Inputs:

– Programmable bus hold provides valid logic level when inputs are not actively driven

– Programmable Interrupt Mask Control for input pins that do not require an interrupt when their states change

or to prevent spurious interrupts default to mask at power-up

– Polarity Inversion register allows inversion of the polarity of the I/O pins when read

? 400 kHz I2C-bus serial interface

? Compliant with I2C-bus Standard-mode (100 kHz)

? Active LOW reset (RESET) input pin resets device to power-up default state

? GPIO All Call address allows programming of more than one device at the same time with the same

parameters

? 16 programmable target addresses using 4 address pins (28-pin TSSOP only)

? -40 °C to +85 °C operation, with HWQFN24 up to +105 °C

? ESD protection exceeds 6000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101

? Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA

? Packages offered: TSSOP28, TSSOP24, HWQFN24

3 Applications

? Cell phones

? Media players

? Multi-voltage environments

? Battery operated mobile gadgets

? Motherboards

? Servers

? RAID systems

? Industrial control

? Medical equipment

? PLCs

? Gaming machines

? Instrumentation and test measurement

產品屬性

  • 產品編號:

    PCA9575PW2,118

  • 制造商:

    NXP USA Inc.

  • 類別:

    集成電路(IC) > I/O 擴展器

  • 包裝:

    卷帶(TR)剪切帶(CT)Digi-Reel? 得捷定制卷帶

  • I/O 數:

    16

  • 接口:

    I2C,SMBus

  • 中斷輸出:

  • 特性:

    POR

  • 輸出類型:

    推挽式

  • 電流 - 灌/拉輸出:

    1mA,3mA

  • 電壓 - 供電:

    1.1V ~ 3.6V

  • 工作溫度:

    -40°C ~ 85°C

  • 安裝類型:

    表面貼裝型

  • 封裝/外殼:

    28-TSSOP(0.173",4.40mm 寬)

  • 供應商器件封裝:

    28-TSSOP

  • 描述:

    IC I2C/SMBUS 16BIT GPIO 28-TSSOP

供應商 型號 品牌 批號 封裝 庫存 備注 價格
NXP/恩智浦
24+
SOIC8
15000
泰盛芯只做原裝現貨
詢價
NXP/恩智浦
22+
SMD
12245
現貨,原廠原裝假一罰十!
詢價
NXP(恩智浦)
2023+
TSSOP-28
4550
全新原裝正品
詢價
TI
TSSOP28
2500
正品原裝--自家現貨-實單可談
詢價
TI
24+
TSSOP28
44300
TI一級代理專營品牌絕對進口原裝假一賠十
詢價
NA
23+
NA
26094
10年以上分銷經驗原裝進口正品,做服務型企業
詢價
NXP
23+
NA
6800
原裝正品,力挺實單
詢價
NXP/恩智浦
23+
TSSOP-28
12222
正規渠道,只有原裝!
詢價
NXP(恩智浦)
23+
NA
6000
原裝現貨訂貨價格優勢
詢價
NXP/恩智浦
21+
SMD
5000
百域芯優勢 實單必成 可開13點增值稅
詢價