P89LPC933中文資料恩智浦?jǐn)?shù)據(jù)手冊PDF規(guī)格書

General description

The P89LPC933/934/935/936 is a single-chip microcontroller, available in low cost packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system-level functions have been incorporated into the P89LPC933/934/935/936 in order to reduce component count, board space, and system cost.

Features and benefits

Principal features

■ 4 kB/8 kB/16 kB byte-erasable flash code memory organized into 1 kB/2 kB sectors

and 64-byte pages. Single-byte erasing allows any byte(s) to be used as non-volatile

data storage.

■ 256-byte RAM data memory. Both the P89LPC935 and P89LPC936 also include a

512-byte auxiliary on-chip RAM.

■ 512-byte customer data EEPROM on chip allows serialization of devices, storage of

setup parameters, etc. (P89LPC935/936).

■ Dual 4-input multiplexed 8-bit A/D converters/DAC outputs (P89LPC935/936, single

A/D on P89LPC933/934).Two analog comparators with selectable inputs and

reference source.

■ Two 16-bit counter/timers (each may be configured to toggle a port output upon timer

overflow or to become a PWM output) and a 23-bit system timer that can also be used

as an RTC.

■ Enhanced UART with fractional baud rate generator, break detect, framing error

detection, and automatic address detection; 400 kHz byte-wide I2C-bus

communication port and SPI communication port.

■ Capture/Compare Unit (CCU) provides PWM, input capture, and output compare

functions (P89LPC935/936).

■ High-accuracy internal RC oscillator option allows operation without external oscillator

components. The RC oscillator option is selectable and fine tunable.

■ 2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or

driven to 5.5 V).

■ 28-pin TSSOP, PLCC, and HVQFN packages with 23 I/O pins minimum and up to 26

I/O pins while using on-chip oscillator and reset options.

Additional features

■ A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns

for all instructions except multiply and divide when executing at 18 MHz. This is six

times the performance of the standard 80C51 running at the same clock frequency. A

lower clock frequency for the same performance results in power savings and reduced

EMI.

■ Serial flash In-Circuit Programming (ICP) allows simple production coding with

commercial EPROM programmers. Flash security bits prevent reading of sensitive

application programs.

■ Serial flash In-System Programming (ISP) allows coding while the device is mounted

in the end application.

■ In-Application Programming (IAP) of the flash code memory. This allows changing the

code in a running application.

■ Watchdog timer with separate on-chip oscillator, requiring no external components.

The watchdog prescaler is selectable from eight values.

■ Low voltage reset (brownout detect) allows a graceful system shutdown when power

fails. May optionally be configured as an interrupt.

■ Idle and two different power-down reduced power modes. Improved wake-up from

Power-down mode (a LOW interrupt input starts execution). Typical power-down

current is 1 μA (total power-down with voltage comparators disabled).

■ Active-LOW reset. On-chip power-on reset allows operation without external reset

components. A reset counter and reset glitch suppression circuitry prevent spurious

and incomplete resets. A software reset function is also available.

■ Configurable on-chip oscillator with frequency range options selected by user

programmed flash configuration bits. Oscillator options support frequencies from

20 kHz to the maximum operating frequency of 18 MHz.

■ Oscillator fail detect. The watchdog timer has a separate fully on-chip oscillator

allowing it to perform an oscillator fail detect function.

■ Programmable port output configuration options: quasi-bidirectional, open drain,

push-pull, input-only.

■ Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value of

the pins match or do not match a programmable pattern.

■ LED drive capability (20 mA) on all port pins. A maximum limit is specified for the

entire chip.

■ Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns

minimum ramp times.

■ Only power and ground connections are required to operate the

P89LPC933/934/935/936 when internal reset option is selected.

■ Four interrupt priority levels.

■ Eight keypad interrupt inputs, plus two additional external interrupt inputs.

■ Schmitt trigger port inputs.

■ Second data pointer.

■ Emulation support.